unijabnx2000's Likes Given

I have to assume if he's not perm-a-banned it's because he has something on someone. How else could this dirt bag still be around? He has absolutely no regard for anyone else and you can see his li...

This situation and Justins responses to it are flat-out unacceptable.

He should be ostracized from our community at every level.

you have to drill out or leave out your thermostat. Recently just had one go bad on me because the seals went out and got the bearings wet and ruined it. $100 for the kit to rebuild it.

Have t...

How is this guy still a part of our community? He's ripped off countless people. And runs one of the dash Facebook pages... It's the one with fewer people on it, but he runs it... And deletes all o...

I want to bring this back from the dead :D

So I went for emissions yesterday and took my laptop with me to do live A/F correction. The tester had zero issues with my adjustments during the test ...

That is a good find.

http://i1317.photobucket.com/albums/t631/lynchfourtwenty/joshs/20141201_175543_zpsp6roodi3.jpg
http://i1317.photobucket.com/albums/t631/lynchfourtwenty/joshs/20141201_175538_zpsdmuscjz9.jpg

Well for now i put the jwt/b15 clutch setup back on since im going 6spd i cant use the fx500 so im selling it.. also put another trans on, its actually all the guts from the one i cracked stuffed i...

Redid my cracked,mismatched and faded trim ,and matched the rear spoiler that had failing clearcoat
http://i.imgur.com/lHpAlcT.jpg
http://i.imgur.com/slG4yVM.jpg
http://i.imgur.com/Zc0DAcv.jpg
...

Do you have the Light weight Fly wheel & clutch for P12/ 6 speed?

$295 + shipping, 1 week to get to me then out to you.

i've let my friend drive the car a few times but he's to afraid to launch it because well.. we know what happens.. lol.. i've driven his car which is setup very similar to mine except he has BC coi...

Nice build, but did you really connect the crankcase ventilation to the charge pipe?
http://i.imgur.com/hM0krAA.jpg
That my friend is a big mistake. You are putting the crankcase under some serio...

18mm drill bit iirc for most top feed injectors. I always just drill them to fit the oring.

My SR20VET still on the stand.

http://imageshack.com/a/img673/1747/0zxuax.jpg

Starting the test fitting process...........

[url= URL=http://s1307.photobucket.com/user/rancherowrap/media/SR20%20Barney%20project/IMG_0318_zpsc8aca5a3.jpg.html][img]http://i1307.photobucket.co...

That hurts my brain. ^

SAVE YOUR MONEY!

Shame on you for even posting such mess Jay....derned Asian people! :D

FTDI232 Drivers can brick your USB to Serial Adapters

B13/B14 Traction Bars

Select forum members aren't getting forum e-mails.

quick update. diff is going well now. had to take it out to address a minute clearance issue with it on the pinions gearstacks. what this did do was quieten the final drive noise down heaps. now i ...

heres a video, the runs were made in 4th gear, only got video of the first run..

http://youtu.be/SS3Hzlz2xtY

With TPS unplugged, if the trans is in neutral and the ECT is at least 140ºF, the ECU enters "SET IDLE/TIMING" mode. If the trans is in gear and the vehicle speed is above 2.5mph, the TPS DTC (cod...

didnt know this thread was about your K24 in your EG...Mr. S. Vang :rofl: