Coheed's Posts

K20's pull premium one-week before race wars!

Nah, just doesn't have the same ring to it. lol

It doesn't take a lot to make awesome power from the K20a/z3.

They just rip from the factory and people have really supported them and pushed the envelope with them. It's not too difficult to get ...

easy way to do ball joints is to unbolt the control arm. It's super easy on these cars. Then use a press to press them out. the "ball joint press" doesn't work too good.

But pressing them out on t...

feels great to have the car back again. And now that I've built a shed I have room to put all my lawn equipment. This makes my 2 car garage fit the super sentra easily with tons of room to walk aro...

I thought I was going to be able to take it easy for 500 miles... ya right. Got the car on the road today. Checked for oil pressure, leaks, and made sure it didn't overheat. About 5 minutes later.....

I've sold several cars in similar shape and swaps for around $5000-$5500.

Getting it to pass emissions, it's not always easy. But that's why i keep my JWT setup. I pass emissions every year :D

I think an asking price of 6500 isn't out of reach.

You know how bad I've been wanting to do this? I'm using the RR dizzy right now, but many years ago I was told the VE dizzy wouldn't work. So I threw it out.

lol. That's called a carburetor silly. :poke:

MSD tach adapter questions

Guys, I have left it off before. DON'T leave it off.

I would hear a strange knock every now and then, when I took the transmission off I could see rub marks on the inside of the bell housing where...

The only reason for this is I don't know how much foreign material made it into the engine while the car was in pieces, and I also don't know how much antifreeze made it into the oil.

When I drain...

I'm just happy to have my car back. Such a relief. I got lucky. Now I warrant everyone on here to take the TB off and drill those screws out if you have to. Get them out, replace them with somethin...

I tried to line up TDC on the crank pulley, but it won't work because the harmonic balancer has slipped... again.

So with the head off, i lined up TDC with the piston in the bore. Then slapped t...

So I got this thing running just now. The IC piping is not completed, but everything else is together, just gotta burp the coolant and hook up the intercooler.

The engine fired right up, first try...

The B13 and B14 FD and LSD can be used in the P11 casing with no change to the final drive gear when using the B15 QG18DE gearstack.

I kept the factory P11 LSD and the QG18 gears swap right in. If...

So... the SR needs 2 things to run... MAF, and distributor. Glad you got it figured out. These cars are so simple.

To check the coil output, hook up an old spark plug to one of your wires. Gap it very large. You want a 1cm gap. If you cannot do this, you will need to buy a spark tester.

It takes 30K volts to j...

There is no fuel in the vacuum lines going to the fuel pressure regulator?

is this a DE or VE?

You have no EGR right?

Just making sure. The SR only needs 2 things to run the engine. The MAF and ...

That is the next thing on the list. I am going to check this asap. I think this may be caused by running the battery to the trunk.

The sentra is back together... sort of. Put the valve cover and intake manifold back on today. Hard to find the time to fix it.

I just need a few touch up things done, hook up IC pipe, fill the oi...

The B13 and B14 pedals are the same or mount up very similar right?

I'm using 17" Rays 57c wheels. The B15 MC looks a bit different. Which is why I think a lot of people go with the altima MC since the hookups are the same.

I'm not debating using the B15 MC, but j...

yeah, actually I'm using the top bolt. It is flanged with a washer-type surface on the head of the bolt. I am using this to pinch the edge of the pedal assembly.

:rofl::rofl::rofl:

Wow man... that was just toooo far! :D

full of win.