Coheed's Posts

lol the car sounds like a tractor in the sound clip haha.

Only the baddest sentra in UTAH BABY!!!

http://i295.photobucket.com/albums/mm158/CoheedJV/DSCN1139.jpg

My blow through setup.

http://i295.photobucket.com/albums/mm158/CoheedJV/DSCN1140.jpg...

I am impressed so far. I pulled right next to my buddies sentra. I know he has to be around 330whp with his disco on 18-19psi. We played a little bit, me with a passenger. He outspooled me and got ...

car is on the road now. I am breaking her in. Feels good, but I hit a lil boost and blew the maf adapter to pieces. It was a plastic one on ebay. The rubber gasket between the maf and the adapter b...

Here are some vids to enjoy...
This one is my buddies disco 98 se. This is a neon that runs 12.5x at 4500ft elevation. The sent has a passenger too.
http://s295.photobucket.com/albums/mm158/Cohee...

I looked at an SE bumper today and I will think about it. It would look nice...

I am too excited to sleep. After a hard day's work shawn has finished the intercooler piping! He is a good friend ...

I don't think there is anything wrong with the arp bolts. I am using them (the new ones) and so far so good. I used them for almost a year on the last build without a single problem.

wow, that is crazy timing. My jwt map pulls timing to 15* when boost hits. This is way too conservative for 10psi, but I have found that when I raise the boost the timing map stays the same. So it ...

Also, the new studs are torqued down to 105 lbft instead of the old one's 80?lbft

I have thought about it, but even still the bumper would have to be cut out like crazy. My buddy has an se bumper and lip combo and it looks nice. But the SE bumper doesn't work as well with these ...

jwt computer. That's it. Got to keep it obd2 legal and this is the easiest way. I might use an safc to tune out the rich map though and i will be playing with the timing in order to get the power i...

I see some really really impressive numbers here! I hope I can post something up in the 400whp range. Prob not though. DET>VET so far. Maybe these VET cams will help??? I will post the dyno as soon...

maybe shawn at tcharged.net can help you. He rebuilds the turbos and balances them. He's helped me a lot. He does it for really good prices too. shoot him an email.

the 3071 is rated to 460. the 3076 is rated to 520. But some WRX guys are doing 550awhp with the 3076 with the .82 housing.

we finished the hot side piping today. All that we need to do is sandblast the pipes and paint them. The cold side is going to take a lil while. The bov is being mounted vertical about 6" upstream ...

VVL will be set at about 6k to start. I may make some small adjustments on the dyno.

Here is the intercooler getting fitted.

http://i295.photobucket.com/albums/mm158/CoheedJV/DSCN1129.jpg

...

omg the intercooler looks soooo good mounted. The car looks so mean! The intercooler was mounted last night and the only thing left to do is cut the bumper a little for fitment and do the cold side...

car is going to have the intercooler mounted tomorrow. right now the car is running na.

give me a couple of days I will have everything done. More videos to follow for sure.

My new intercooler. Shawn says hi!

http://i295.photobucket.com/albums/mm158/CoheedJV/DSCN1127.jpg

replacing the old one. Not going to be as sleeperish now.

http://i295.photobucket.com/albu...

I am crossing my fingers on these VET cams, hopefully they will make power lol. I really wanna see this thing hit some high numbers. Shooting for somewhere around 375-400whp on pump 16psi. Maybe th...

I appreciate all the good comments coming. Makes me feel like I am doing it right.

I thought the stock valves were 31mm??? I measured mine at 31.5mm just a couple days ago for the intake. I know because my good friend has bigger valves in his 3sgte celica motor and we compared hi...

thank you miko! Without your block it would have taken even longer. Thanks again for all your help.

here are more pics! Motor in!

New prothane motor mounts installed. These were hard and easy...

I am running the z32 maf. I have everything I need to convert it. The motor and tranny were installed yesterday. I will post pics of everything. Car is not running YET, but will be soon! I will kee...

I will be trying to get some video of the starting of the car either today or tomorrow. I should be able to get her running so we can get some intercooler piping fabricated next week. The biggest d...