Coheed's Posts

bearing for what? the diff?

I think a bottom mount TS is a great idea, wastegate placement is going to be interesting though. I think most feel comfortable in the $1200-$1500 range max. Simpler designs should be around $1000 ...

middle shift rod? It will come out once you have pulled all the check balls out and taken the shift forks off.

Got any pics of what you're talking about?

^^^
thats what I did. Pretty straight forward. Just don't use a crappy tap set like I did, they are good once. So if you only need it one time, then it will work just fine.

I've bought 2 OEM cables from the dealer and both were too mushy feeling. The lube inside them had dried up and required me to re-lube them. After that, they worked great.

... But, I've used the ...

Nah, I'm definitely keeping it USDM on the parts. I need to be able to replace these things every now and again, or at least find replacement parts quickly.

Yeah, if I could find an N15 front I would do it. But I don't have the means of getting one, let alone hacking it up to fit my intercooler/heat exchanger.

The 1999 rear bumper looks the best imo, but the front is too bubbly. The nice round cutout for the muffler tip is nice :D

I guess the 1999 bumper is nice, especially without the cutout for the li...

EURO CHROME CRYSTAL HEADLIGHTS WITH AMBER FOR NISSAN | eBay

^^^ That is sorta what I am looking for. I have the 1999 headlights and bumper right now. But I am thinking the clear headlights instead of the black housing ones. But with the clear ones, I was go...

Best B14 headlight/bumper combo

I've got more pics coming. The cutouts, and underneath the car.

Here is a pic I found of the MR transmission 6 speed. Looks like an RS6 trans to me. And the weakest link comes with 4th gear. You can see it is smaller. But on a FWD, I can see this holding up a l...

If you guys are talking about this clip seen here
http://i295.photobucket.com/albums/mm158/CoheedJV/transmission/DSCN2570.jpg

You have to bolt the trans all together and when the cases are bolted ...

The tires sit nearly flush with the fenders. Spacing them out any farther would mean they would rub the fenders. If anything the track seems wider than before. The rear of the B14 shows that with s...

Somehow those numbers aren't right. 1st only gets me to 45mph. 2nd is only about 70 maybe 75mph.

At 8800rpm
1st 52mph
2nd 84mph
3rd 117mph
4th 154mph
5th 201mph
6th 242mph
with a 25.7" tire.

That is just nuts.

I am actually going to get the car aligned in a couple hours. I will scan the results I get and post them up.

I do not have castor bushings installed... yet. The suspension tuning begins this y...

You can skim the head, that might do the trick. But check the piston quench clearance and valve clearance. I forget that the SR16 pistons are built a bit differently than the 2.0. But keep the 1.6 ...

Well guys, 400 miles on this thing and it is doing great. The HLSD works like a charm. But I do have one question.

Changing from the stock SEL wheels, to the 57c wheels, the offset has changed a b...

Enjoy the swap.

http://i73.photobucket.com/albums/i217/trollin123/UN%20BBQ%20sugar%20house%202011/IMG_0123.jpg[/QUOTE]


http://i73.photobucket.com/albums/i217/trollin123/UN%20BBQ%20sugar%20house%...

Here's some progress I made with mounting the shifter, and having the flywheel machined. You may or may not have to have machining done.

http://i295.photobucket.com/albums/mm158/CoheedJV/transmiss...

Now you have to transfer all the old bearings over to the new trans bell housing. The bell housing is sold without an parts really. It has new seals installed, but that is about it.

Mainshaft bear...

This is what I did today. I'm going to just put my write-up here for now until I get a full sticky thread for just that. But you guys can at least see what is involved. This is a rather simple job,...

You need any KA24DE clutch kit. Get one to suit your needs. I got this one from Greg V. It wasn't cheap, but the thing feels amazing.
http://i295.photobucket.com/albums/mm158/CoheedJV/transmission...