All posts made by jonwepa
Well we are going to have another no2 powered VE..
OK.....I am going to try everything from 5500-6500 and see what works best.
Out of curiosity what are you revving too??
I will try those 5600-5800. It was funny because i had my mss set at 4900and 5000 and it was horrible....WAY to soon for the n1's
I am getting it tuned today by driving it around with a WB and l...
subscribed for availability date...
AWESOME website:bigthumbup: I used to use it and couldn't find it. Thanks
As foe the issue at hand stick with what the manufactuar says, although jets are jets really and are the same for all ki...
Zex's chart says 26fuel and 46 No2 now thats only probably 85 to the wheels...
here is the chart
http://www.zex.com/catalog/ZEX101-05/PG22.pdf
switch over points for N1's??
I just was having a issue comprehending the whole process. i still have yet to fill the tranny with fluid and try it out. Also I didn't hook up any sensors either, so I have to figure that out stil...
Ok guys I got it. The grinding was definitely needed and i might need a tad more because getting into reverse is a little hard, but its done.
THANKS for all the help and especially the pics!
Unless greg V gave me a wrong tranny......:o
NOT
And this is the best picture so far. I removed that bracket for the second arm and I shouldn't of. I think I may finally understand....I t...
I had not one issue mounting my sr16 tranny
Thats my next plan
The tranny and motor are lined up perfectly, but its tilted so I plan to loosen the c member and lined it up.
Next i just have to work on this TOB issue. The bearing se...
I did grind the hole where the lever goes down, but it seems to go in nicely....
As for the arm I just bent the air tube down.
This is why I wish i just got another sr16 tranny.....
I wil...
You talking to me?? If so I would love the help. The only thing is I may be working saturday, but will definitely be around SUNDAY. Pm me if you do, if not Sorry for the misunderstanding:o
whats going on here with the secrets?? I have N1's not installed because I am curious on what these will do...Can somebody pm me here....
My bracket isn't even close to them 2 holes above. Thats the problem. The 2 dowl pins line up perfect the bolt holes line up, but the bracket above is off prett bad, so i might have to atleast loos...
Thats my plan. I just wanted to make sure there wasn't something i missed. As for me being a lost cause thats not really fair, I might be impulsive and have trouble listening( hence my meds :rofl:)...
Well it has to matter bwecause the one i am using binds up on the shaft.....and then breaks away from the clips. I never seen so many isses in installing a simple trans.
I think I am going to l...
Again I have installed about 10 trannys and this one is not working! I just took off a sr16 that had 4th gear popout and and that I INSTALLED and it didn't have this issue, so i know how:mad: Its n...
How aboput the TOB?? Does it have to be a 2000 sentra one or does it even matter?? Because the one i am trying to use is binding and when i had the tranny bolted up except the back mount the TOB ca...
Also guys the sensors I took from my last tranny dont wire or fit on the new b15 how do you make them work or are they even nessacary?
I am about to just trade it and for a sr16 and cash... Alot...
That was easy....but when you look in the back(towards the firewall) its just totally off????? All the dowpins lined up. All the bolts tighten right up, its just the rear mount is off and the moto...
I have everything lined up right, but i guess i will have to fiddle with it more?????
Also what about the TOB? DO i need a 2000 se one? Because the one i tryed using is getting binded, so i thin...
B15 tranny not lining up with rear mm bracket???
Does a b13 sentra RSB fit a NX?