Coheed's Posts

RS6 6 speed parts

So there still seem to be some issues with how I am going to do this. I am really debating hard on getting some SpecV hubs with brembos and the whole rear beam. I just really didn't want to have to...

If you are paying over $400 for a QG transmission you are getting ripped off. You can find whole transmissions on car-part.com for $200-$400 all day long.

Very low mileage <40K miles for $400-450 ...

Ya I can tell you from experience that the heavy does a good job of cushioning the gears. The first trans I had lasted 2 years with heavy shockproof and a sprung clutch. Didn't break until I change...

Nice carnage. I've broken 4th twice. 3rd once. 2nd once. lol. Gotta use heavy shockproof in there man. It will make them last a ton longer.

The QG stacks work awesome!

Here is a direct side-by-side comparison of the gearshafts.

http://i295.photobucket.com/albums/mm158/CoheedJV/transmission/DSCN2727.jpg

http://i295.photobucket.com/albums/mm158/CoheedJV/trans...

Now you have to transfer all the old bearings over to the new trans bell housing. The bell housing is sold without an parts really. It has new seals installed, but that is about it.

Mainshaft be...

This is what I did today. I'm going to just put my write-up here for now until I get a full sticky thread for just that. But you guys can at least see what is involved. This is a rather simple job,...

Very well said.

I haven't looked at the Maxima clutch pedal yet to see if it just drops in. But looking things over, I doubt it. If anyone can CONFIRM without speculation, then I will go for it. I think I may look...

Ok some info I have found doing research in my FSM collection. Not sure this is going to work, but I'll run it by you guys here real quick.

When talking with Marty at RAXLES, he said when he took ...

The Altima axle uses a BF90 outer joint. So it is not compatible with specV axles i don't think.

Ok, I think I have caught a break. The CV axles for the SR and GA are different, but the outer CV on the GA has the same internal spline as the QG. QG is the same as the specV so I think I have an ...

Someone answer this!

E85 is awesome, but the fuel demands make it very low on my list. Plus, you can always make more power with real race gas. There are a lot of downsides with E85. Great for a race car though. But st...

here's how the car sits now. :( sad seeing her like this. But seems to happen every year or so at some point lol.

http://i295.photobucket.com/albums/mm158/CoheedJV/transmission/DSCN2591.jpg

Okay here's the goods!

http://i295.photobucket.com/albums/mm158/CoheedJV/transmission/DSCN2582.jpg

http://i295.photobucket.com/albums/mm158/CoheedJV/transmission/DSCN2583.jpg

http://i295.photobu...

Just a basic sprung disk. Keep the wheel hop in check at all times. Run heavy shockproof. You should get a better life from the new stacks.

Yes sir. I've gotten pretty much every part for this project from Greg. He's the Best!

All the stuff I could find on the specV trans under real abuse was from the maxima/altima guys. They seem to have pretty good luck with them until over 400wtq, but keep in mind they are pushing the...

took some measurements today and the B14 and B15 wheel bearings are exactly the same with the exception of the inside diameter. So I could technically keep my B14 brakes. I would just press out my ...

I got the Mount kit today. And I have to say the quality of the Mazworx parts is TOP NOTCH! I am impressed.

After talking with Marty again, he still cant remember how he did the axles for Iczer20...

Ya the SpecV/Maxima trans is rated at a working 230lbs torque, but the Maxima makes more torque than that! Nissan still uses the RS6 trans in the Maxima, because it works and still doesn't have fai...

I am at a loss for words. There is so much wrong with that article, it isn't even worth me bringing everything up. Just. Delete.

It is about 180lbs iirc.