Coheed's Posts

http://i295.photobucket.com/albums/mm158/CoheedJV/transmission/DSCN2544.jpg

http://i295.photobucket.com/albums/mm158/CoheedJV/transmission/DSCN2545.jpg

http://i295.photobucket.com/albums/mm158/CoheedJV/transmission/DSCN2538.jpg

http://i295.photobucket.com/albums/mm158/CoheedJV/transmission/DSCN2537.jpg

http://i295.photobucket.com/albums/mm158/Co...

Oh wow! there are a ton of pictures. This is going to take forever. But I will say that I had time to mount up the new altima clutch pedal. It doesn't look like its going to work. The top bolt wher...

holding a steady 200+whp for any amount of RPM like that would make the car a very potent NA ride. Good stuff man.

Wow, today was a day! I had a headache from hell all day long, but i REALLY wanted to work on this project. I've got everything coming for this swap but need a new clutch. Other than that, everythi...

dynojet numbers are my favorite, because there is less chance of dyno operator error. On a dynojet the numbers seem low. 300whp comes rather easily on just 15psi with a disco potato. That big turbo...

Yea what other people say about the timing is true. I gained 60whp from around 4* timing iirc. It was ridiculous.

But if the timing is on, regardless of that afr, it is a pretty low dyno number. S...

Good to hear your input Cozzm0. The way I see it, the 6-speed is more available if you break it, but it is a little bit more work to put another one in.

I love the fact that the P11 box holds 350w...

Using the KA24DE clutch to go with the Gspec Flywheel.

Yea, I just cant find a yard around here that will sell the spindles for less. I also don't want to have to upgrade brakes quite yet. The AD22 work ok for what I'm doing. I will go bigger soon enou...

You can run a slightly stiffer BOV when venting to atmosphere because the stiffer BOV won't allow unmetered air in under idle.

When you pull a vacuum you want to see it hold about 20-25in because ...

Also greg we really should get a clutch hose as well. I can have one made locally, but if you happen to know what length is required it would be helpful. Or you can just have one made and sell it ;)

I had Marty @ Raxles start making me a set of Spec V axles that will work with my current hubs. He quoted me $225 per axle and around $500 shipped for the both of them. So the way I look at it is l...

6-speed swap stuff

I got some parts today.
Transmission with 47K miles on it.
Clutch pedal assembly from a 98 altima (not sure if it will work)
new sunvisors for the wife's car. hers were broken. put 04 sunvisors in...

brake booster won't cause a sponge pedal/soft pedal. It will cause a very hard pedal with little to no assist.

JE 8.5:1 VE-T pistons.

I think for 450whp the GT3071r is your best bet. It will do 400whp rather easily, but won't surge like the GT3076r can on a small housing. The .82ar rear housing is the on...

Right on bro. I haven't seen much wear on thrust bearings with the SR motor. So it is good to see this isn't an issue with these cars.

In case anyone wants to hear this:

When changing calipers it makes it a very simple and fast way if you have a few pointers to assist.

Applying the brake pedal even just slightly will block off ...

lol x2 on the rotors. That would def cause problems.

Well, as far as bleeding goes; I let gravity do its thing. Just crack a bleeder and have a hose off the bleeder drip into a drain pan. Keep the...

Awesome work man. Incredible.

I have not come to a conclusion on this yet but I am thinking the extra size of the shafts is going to reduce flex in the shaft a lot. When I take it apart I will see.

The GT30r will get you there, and it loves high boost. Mine has been good to me. I just cant push more than 24-25psi through the maf without fear of it blowing up eventually. So I am stuck around t...

Top picture is a V6 6 speed from an altima. This is in Ninty-9 SEL's car.

Yes sir. Bottom is P11. Problem is, I can't really see how this transmission is "stronger"