Coheed's Posts

Yes sir, I like how they hide it really well while it is in the car. but when you pull the engine it's right there!

The 2zz is a good motor, but I agree it does kinda respond poorly to mods. I k...

What I am saying is, what would you need to do to make a sentra compete. Not what I need to do. This thread has somehow been aimed toward myself because I am the OP. It is a simple objective questi...

I got some video tonight. With the exhuast on you can hear the turbo a lot better.

But first, a video of 10psi on the old motor revving to 7300rpm.

YouTube - I got vtak 10psi.MOV

New vide...

The b14 requires a tach adapter. I ordered on but havent gotten it yet. There is no coil kickback signal to the ecu so it triggers a cel for misfire.

you are getting too much tread squirm. Raising the pressure on your tires reduces rolling resistance. That's why you're faster.

Just plug in your EGR stuff, it doesn't actually have to have the EGR valve. Just plug in your temp sensor and the EGR solenoid, zip-tie outta the way, done.

Thank you lynch, I just got back from getting the car registered. It passed the emissions test! Woooot!

Right as I drove off the CEL came on for no cat lol. So I hooked my MSD back up and starte...

Well, if the noise goes away at all while the clutch is pushed in, it is likely a bad input shaft bearing, or perhaps a TOB?

The trans isn't going to make noise unless something is really wrong....

I think people confuse spool with boost onset. The boost onset on a dyno graph will show similar results, but I could show you a GT4202R spooling like a GT35R. But the response? Forget about it, th...

Buy a new one, unless it is a p11 or b15 tranny.

40-120mph in 12 seconds. I guess it is pretty slow. But it is only 10psi. I still bet over 300whp. You gotta figure, I am at 4500ft elevation as well.

I actually just looked at some old video I ...

Actually on the top of 3rd it was doing approx 120-121mph. I granny shift. That mark on the gauge is 120mph. Not 110.

The car runs 2% larger tires also, so that 120mph is more like 122-123ish.
...

12.3, come on now I am running street tires. But I was wondering what whp. Well, considering 15psi was 361whp on the log manifold and VET cams, I am going to say 10psi now is 325whp, but the car is...

took the car for a drive through the canyon today. Man it felt so good. The hypercos and AGX handle so well on the B14. It corners flat, and doesn't oversteer like stock since I took the front roll...

But that's granny shifting. I wanna double clutch ;)

The DE bearings work in the VE. No issues. I used to spend money on "good" bearings. I feel like it was money wasted. I am running stock bearings now, clevite DE bearings.

Any bearings will work. But the VE crank bearings have more oiling holes in them.

Yes, from time to time it can happen with some vehicles. Who knows why. I ohmed mine, checked pins and connectors etc and always got that stupid code.

Buy a cheapo. not worth spending so much money on a silly knock sensor.

YouTube - The Super Sentra running 10psi

My buddy made this video with some footage from last night. Not the greatest footage, but hopefully you guys like. Motor runs sooo good. I just am very h...

BILLET WHEELS are pointless?

Raised the limiter to 8800rpm. Car feels incredible for 10psi. I will get my friend to post some vids. My stock tach isn't that far off. It shows just under 9K when I hit the limiter. 3rd gets to 1...

Wow, your tach is way off. Mine shows 8500rpm at the limiter of 8300. Only 200-300rpm off at the most.

The MSS has a shift light built in ;)

I think the motor feels great at high rpm. Very sm...

Just takes time and patience. Teach yourself, share your experiences, and keep learning. :)

I am going to raise the rev limiter and try to finish the 1/4 mile tonight in 3rd gear on 10psi. See w...

I have springs and retainers. with SR16 cams. So 9K shouldn't be a problem.