Coheed's Posts

I get where ben is coming from. It is just a really complex topic that will require one to their research.

Everyone here wants to contribute, and we do freely. But something as complex as this ...

My Full race GT3076r twin scroll now works - Mitsubishi Lancer Register Forum

I have contributed some of my findings in this thread, but he has changed the 1.06 housing and a cam upgrade. Made o...

Bringing this one back. With an update...

I put the stock VE cams back in, but haven't gotten to dyno yet. I have since decided to change the setup slightly. But Datascan shows that maf voltage ...

Rotella 5w40, German castrol... best oils.

If you use mobil, make sure it is the high-mileage stuff... better additive pack. 10w40 high mileage is the OLD 15w50 racing formula.

i wonder if i have this going on in my engine. But i am no sure now. My oil pressure usually stays around 40psi at idle, but drops to about 25 or so after lots of beating. I have a GTiR pump. But i...

Fail safe thermostats don't fail open. They just lock open during an overheat to allow maximum coolant flow. The 'Zone sells them too. You can unlock them if they ever lock open, but like any therm...

Wow, just.... WOW!

Whether you bought the product direct, or through a vendor, or another person, it was new. that is BS.

well if you got oil and coolant mixed then it will look like chocolate milk in there. Happens. But that is bad luck. Time to swap in a DET and keep that one for a backup heh heh.

I never retorqued the studs on mine, but just torqued them to the full spec. I thought the studs would rip the threads out of the block. Serious torque for aluminum. Scary.

I have a new cap, fully purged system. 16psi cap iirc from the 300zx.

I have experienced some of the same issues. I have the NEW ARP head studs, the 220K psi strength ones. Torqued to 108lbs. A...

E85 doesnt create water, but it does mix with it. If you get condensation or any amount of water in the tank it can cause big problems.

I used an entire can of starting fluid trying to start my...

springs come out, it is a fact of life. You either need to be careful on the shifts and launch, or get a disc unsprung.

when I sent them a chip for reprogram it took three weeks to get the new chip :(

I hope they are faster now, because I need my limiter removed.

I will be testing them one at a time. Remember 24psi up here is still only like 20-21psi at sea level. 450whp ain't bad, and I am making more power than that now with the stock VE cams. Maf voltage...

no thoughts on a N1 cam on a divided 1.06 housing huh? 36 views and noone has any thoughts?

Well the thought is the backpressure will be minimized with the larger housing, as the .78 seems too r...

I've done 442 on pump, but I'm sure I could do more. I don't wanna push it though, that was 24psi!

pump gas and 400whp seems to be the magic number unless revving really high, or large-frame tur...

Some thoughts on this setup

Have you seen my sig? Not bad for pump gas with a car loaded. I won't be doing that anymore :rofl:

some may ask how NA cars react to E85 and if you can make more power. The answer is yes! Why?

E85 has less BTU of energy per gallon than gasoline. How can it make more power than gasoline if it ...

if you can't get it at every gas station, it isn't pump gas.

85-93 need only apply. Not E-85, sorry ;)

pretty sure the damage is just on the case. I'd bet the rest of the trans is fine as long as you didn't get debris in there. Which you prob didn't.

Clean everything out and put on a new case and...

hey guys, i work at the big A. You get what you pay for, which is why they offer the goodyear OEM replacement. You have to order it in most cases but it isn't cut to fit like the cheaper kelly spri...

that is very impressive for a t2 3071r. What ex housing you running? I am running 26psi on my 3076r, and my maf is reading over 5V heh heh. I will soon have to turn down the boost and get more revs...

Very illegal.

YouTube - Super Sentra compilation

I've found that putting the maf under blow through causes it to max out faster, so if you are really going for a ton of power you may want to log the maf reading to make sure you aren't getting ove...