Coheed's Posts

I have noticed one thing with the synchromesh under long drives. After cruising on the freeway for over 20min at 80mph or so there was some noticeable gear noise under slight-decel. As soon as the ...

If you have the B15 trans, you could get the P11 gearstacks from a QG18 tranny, along with your 4.176FD, and swap the 5th gear over from the B15 SR stack to the QG stack. That would be cheap. Just ...

If you want the longer 5th for low rpm freeway driving, you will want to keep a SR B15 5th gear and put the gears onto the QG or P11 stacks. The QG and P11 stacks mate up with all 4.176 FD gears AF...

UUUUUHHHHHHHHT OOOOOOOOOOOOOHHHHHHHHHHHHHH!

Ashton I have this exact same problem with mine. My oil pressure running 20w50 is getting around 25psi at idle. I never had this low of pressure befor...

Yes it is rediculous. I am running 20* right now on the top end on 24-26psi(depending on temps outside) and I am running 100 octane fuel. Of course, 24-25psi up here is like 21psi at sea level when...

16* total timing? Post up your timing map.

I like to relate the HP/TQ to electrical power and voltage. Power and voltage are related, yes. But the same? No.

Power is VoltageXAmps=Watts (or horsepower). Think of Voltage as your rpm, and A...

Well, considering I am the only one so far to have ANY issues... I think it will go well the next round.

The other wastegates are very big and won't fit in the bay. The entire manifold was made for these gates.

They were from ATP. There is little chance of them being knockoffs since they are so new to the market still.

I think I got a batch that was thrown together honestly. I mean, I had problems with these gates sticking open since 2 weeks after the car was running.

Ya autozone ones are like $40 and are identical to the newer style VE ones.

??? Who knows. But there isn't a lot of really hot stuff going on. The turbine is still black, and normally when EGTs get out of hand they will turn bright white. There is a little discoloration, b...

Wow, noone has broken 250whp with a simple setup yet? How far can N1 or 20V cams get you before you need an upgrade?

I made 170whp stock. Larger valves should make for a bit of power increase. T...

I think a nice SR20ve could be made with high compression, N1 cams or bigger, and lots of head work and E85 fuel.

Got them both ready to go back tomorrow. This leaves me driving the wife's car now. Sigh.

Well the good news is that I found out there is a lot more left on the table with a tune. So a new inte...

I am not really sure you will need to take out that much overlap as long as you have a free-flowing exhaust side. JP swapped in the 16ve cams and gained pretty much everywhere.

??? any news?

It says "DO NOT ADD OIL"

I would just do what it says ;)

That looks like the sludge monster lol. Vadim can let you in on some secrets to get that baby nice and shiny. It should work great af...

RRRIIIIIIIIIIGHT :poke:

I should put my rom dump on here. Looks like I should be around 24-25* advance according to most tunes, on around 24psi of boost. However, I am at 20* peak on 24psi. I did recently make about 60whp...

Well, here are my thoughts, not that it matters.

The exhaust pulses go through the collector at different times, so the collector size shouldn't affect power too much. Also with longer runners ...

I think msd sells a knocklite that just flashes when you hit knock. I like these boxes and one of my friends has used it for years with very good results. He relies on water/meth to keep knock at b...

for NA? I don't think anyone has used them for turbo yet. (and posted results anyway)

You are our only hope. lol.

http://i295.photobucket.com/albums/mm158/CoheedJV/DSCN2199.jpg

http://i295.photobucket.com/albums/mm158/CoheedJV/DSCN2200.jpg

http://i295.photobucket.com/albums/mm158/CoheedJV/DSCN2201.jpg

...